View MNR35J5RJ_1282082.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MNR35
Resistors
Chip resistor networks
MNR35 (1206x5 size)
Features 1) Common terminals yield area 40% smaller than that of the MNR38. 2) 8-element construction makes the MNR35 ideal for bus line pull-up / pull-down. 3) Convex electrodes Easy to check the fillet after soldering is finished. 4) Compatible with a wide range of mounting equipment. Squared corners make it excellent for mounting using image recognition devices. 5) ROHM resistors have approved ISO-9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it.
Ratings
Item Rated power Conditions Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70C.
100 80 60 40 20 0
Specifications 0.063W (1 / 16W) at 70C
POWER LOAD (%)
-55
0
70
100
125
AMBIENT TEMPERATURE (C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V)
E= PxR
P: Rated power (W) R: Nominal resistance ()
Limiting element voltage
50V
Nominal resistance Operating temperature
See Table 1.
-55C to +125C
Table 1 Resistance tolerance Resistance range () Resistance temperature coefficient (ppm / C)
J (5%)
56R100k
(E12)
200
*Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage.
Rev.B
1/4
MNR35
Resistors
Characteristics
Item Resistance Variation of resistance with temperature Overload
Guaranteed value Resistor type
Test conditions (JIS C 5201-1) JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : -55 / +25 / +125C JIS C 5201-1 4.13 Rated voltage (current) x2.5, 2s. Maximum Overload Voltage : 100V JIS C 5201-1 4.17 Rosin*Ethanol (25%WT) Soldering condition : 2355C Duration of immersion : 2.00.5s. JIS C 5201-1 4.18 Soldering condition : 2605C Duration of immersion : 101s. JIS C 5201-1 4.19 Test temp. : -55C to +125C 5cyc JIS C 5201-1 4.24 40C, 93%RH Test time : 1,000h to 1,048h JIS C 5201-1 4.25.1 Rated voltage (current), 70C 1.5h : ON - 0.5h : OFF Test time : 1,000h to 1,048h JIS C 5201-1 4.25.3 125C Test time : 1,000h to 1,048h JIS C 5201-1 4.29 235C, Immersion cleaning, 50.5min. Solvent : 2-propanol JIS C 5201-1 4.33
J : 5% See Table.1 (2.0%+0.1) A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. (1.0%+0.1) No remarkable abnormality on the appearance. (1.0%+0.1) (3.0%+0.1)
Solderability
Resistance to soldering heat Rapid change of temperature Damp heat, steady state
(3.0%+0.1) Endurance at 70C (3.0%+0.1) Endurance (1.0%+0.1) Resistance to solvent (1.0%+0.05) Without mechanical damage such as breaks.
Bend strength of the end face plating
External dimensions (Unit : mm)
6.40.4
Cross section A-A'
2
B
6 1 1 1
1.27
1
Material
5
Max.0.5 0.50.3 3.10.2
A
A'
R103
Cross section B-B'
61
1 2 3
Thick dielectric glaze of oxide metal (only silver used for jumper) Thick film of silver for electrode Nickel-coated electrode External electrode coated with Sn Alumina substrate Overcoating
5
B' 0.50.2 0.550.1
2
3
4
4 5 6
1.00.2
0.80.2
Pitch of the upper electrode.
Rev.B
2/4
MNR35
Resistors
Equivalent circuit
R8
R7
R6
R5
R1
R2
R3
R4
R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8
Packaging
Reel Taping
P0
P2
D
0
08
06
04
A
B
D
02
W F
B0
E
02
04
06
08
A0
P1
K
C
Label
EIAJ ET-7200B compliant
(Unit : mm)
W 12.00.3
F 5.50.05 P0 4.00.1
E 1.750.1 P1 4.00.1
A0 3.40.1 P2 2.00.05
B0 6.60.1 K 1.00.15
(Unit : mm)
A 180 0 -1.5
B 60 +1 0
C 13 +1.0 -0
D 130.2
D0 +0.1 1.5 0
Product designation
MNR3 5
Part No.
J5R
J 5% J is also used for jumper
J
Nominal resistance
Resistance code,3 digits, 000 denotes Jumper type.
Resistance tolerance
Packaging Specifications Code
Part No.
MNR35
Code
J5R
Resistance tolerance J(5%)
Packaging specifications
Embossed tape (4mm Pitch)
Reel
180mm (7in.)
Basic ordering unit (pcs)
4,000
Reel (180) : JEITA ET-7200B : Standard product
Rev.B
3/4
MNR35
Resistors
Electrical characteristics
TEMPERATURE COEFFICIENT (ppm / C)
6.0 5.0 4.0
DC RESISTANCE (%)
400 300 200
R/R (%)
6.0
JIS C 5201-1 4.5 SAMPLE SIZE : n=40pcs 20C 65%RH
JIS C 5201-1 4.8 SAMPLE SIZE : n=16pcs 25C / -55C 25C / 125C
4.0 2.0 0 -2.0 -4.0 -6.0
3.0 2.0 1.0 0 -1.0 -2.0 -3.0 -4.0 -5.0 -6.0 10 100 1k 10k 100k
JIS C 5201-1 4.13 SAMPLE SIZE : n=16pcs RATED VOLTAGE x 2.5TIMES 2s MAXIMUM OVERLOAD VOLTAGE : 100V
100 0 -100 -200 -300 -400 15 100 1k 10k 100k
10
100
1k
10k
100k
RESISTANCE ()
RESISTANCE ()
RESISTANCE ()
Fig.2 Resistance
Fig.3 Variation resistance with temperature
Fig.4 Overload
3.0 2.0 1.0
R/R (%)
R/R (%)
3.0
6.0
JIS C 5201-1 4.19 SAMPLE SIZE : n=16pcs -55C / 125C 5cyc
JIS C 5201-1 4.18 SAMPLE SIZE : n=16pcs SOLDERING CONDITION : 260C 10s
2.0 1.0 0 -1.0 -2.0 -3.0
4.0 2.0
R/R (%)
JIS C 5201-1 4.24 SAMPLE SIZE : n=16pcs 40C 93%RH WITH NO LOAD 1,000h
0 -1.0 -2.0 -3.0
0 -2.0 -4.0 -6.0
10
100
1k
10k
100k
10
100
1k
10k
100k
10
100
1k
10k
100k
RESISTANCE ()
RESISTANCE ()
RESISTANCE ()
Fig.5 Resistance to soldering heat
Fig.6 Rapid change of temperature
Fig.7 Damp heat, steady state
6.0 4.0 JIS C 5202 7.9 SAMPLE SIZE : n = 16pcs 60 C 95%RH 1,000h OVERLOAD : THE RATED VOLTAGE
R/R (%)
6.0 4.0 2.0 0 -2.0 -4.0 -6.0 JIS C 5201-1 4.25.3 SAMPLE SIZE : n=16pcs 125C WITH NO LOAD 1,000h
2.0 1.5
RESISTANCE CHANGE (%)
JIS C 5201-1 4.29 SAMPLE SIZE : n=16pcs IPA, 5min.
1.0 0.5 0 -0.5 -1.0 -1.5
2.0
R / R (%)
0 - 2.0 - 4.0 - 6.0
10
100
1k
10k
100k
10
100
1k
10k
100k
-2.0
15
100
1k
10k
100k
RESISTANCE ()
RESISTANCE ()
RESISTANCE ()
Fig.8 Endurance (under load in damp environment)
Fig.9 Endurance
Fig.10 Resistance to solvents
Rev.B
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1

▲Up To Search▲

Price & Availability of MNR35J5RJ

	To Download MNR35J5RJ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .